Hot sauce for your X30

The Sombrero appreciates the nightlife and likes to enjoy a little more petrol. During his last visit to a disco, he discovered his preference for particularly large-volume 17 mm carburettors and powerful resonance flutes. Are you ready for a hot dance?

New

Set

Puch

35720

GPO 41 mm tuning set "Sombrero" | Puch X30 Velux

Manufacturer: GPO · Manufacturer: NGK · Manufacturer: swiing® ingenious parts · Material: Gray cast iron · Displacement: 57 ccm · Nominal diameter: 41 mm

614,60 EUR

Set

Hot

Puch

34863

GPO Ø 41 mm "Sombrero" cylinder kit | Puch X30 Velux, NG-2AH

Nominal diameter: 41 mm · Manufacturer: GPO · Material: Gray cast iron · Displacement: 57 ccm · Crankshaft stroke: 43 mm · Ø cylinder neck: 44.7 mm · Ø outlet inside: 25 mm · Ø Inlet inside: 19 mm · Thread inlet: M6x1 (standard thread) · Hole spacing inlet: 32 mm · Ø piston pin (B): 10 mm · Ø piston pin (B): 12 mm · Outlet type: straight · Hole spacing outlet: 42 mm · Thread outlet: M6x1 (standard thread) · Number of fixing points: 4 pcs · Hole pattern [mm]: 44 x 44 · Decompressor: No · Camouflaged: No · Area of application: Tuning

223,40 EUR

Puch

32389

GPO cylinder gasket set BAD ASS Lucifer / GPO Sombrero 41 mm | Puch X30 Velux, NG-2AH

Manufacturer: GPO · Material: Aluminum · Material: Sealing paper · Area of application: Tuning · Ø cylinder: 41 mm · Hole spacing inlet: 32 mm · Thickness: 0.4 mm · Thickness: 0.45 mm · Ø outlet inside: 27 mm · Hole spacing outlet: 32 mm · Decompressor: Yes · Number of components: 4 pcs · Hole pattern [mm]: 44 x 44 mm

22,20 EUR

Puch

32001

GPO cylinder base gasket BAD ASS Lucifer / GPO Sombrero 41 mm | Puch X30 Velux, NG-2AH

Ø inside: 45 mm · Nominal diameter: 45 mm · Manufacturer: GPO · Material: Oiled paper · Thickness: 0.5 mm · Place of use: Cylinder base · Hole pattern [mm]: 44 x 44

11,10 EUR

Puch

32000

GPO inlet gasket BAD ASS Lucifer / GPO Sombrero cylinder | Puch X30 Velux, NG-2AH

Place of use: Admission · Manufacturer: GPO · Material: Oiled paper · Ø inside: 18 mm · Thickness: 0.5 mm · Ø screw holder: 6 mm · Hole spacing inlet: 32 mm

7,70 EUR

More collections

GPO «Pomodoro» Tuningzylinder

The sun-ripened ‘Pomodoro’ tuning cylinder for Sachs 503 engines is the alternative to comparable racing kits and impresses with its freshness in the lower rev range as well as its powerful bite in the form of acceleration and pulling power. It also impresses with a juicy finish in the upper rev range.

23_10-mklt-collection-swiing-17-vergaser-01msc

swiing® ingenious 17 mm SRF carburettor

The new swiing 17 mm carburettor gives you a real boost with its original look. Perfectly camouflaged on the outside, top performance for your moped on the inside. Available with matching intake manifold for Puch E50 and Z50.

Tyre sets

As far as we know, it has never done any harm to simply replace both tyres on a moped. Rubber simply becomes more brittle over the years. We have put together high-quality tyre sets for you with competitive set prices.

Mofakultwear helmets

Helmets from Mofakultwear don't just look good, they should be good too. That's why they are handmade in Italy. Our models are all ECE-R22.05 approved and are absolutely roadworthy. So that you always have a good feeling when cruising.

23_10-mklt-collection-swiing-evo-zündung-01msc

swiing® ingenious EVO ignition

Thanks to a flywheel weighted as standard, it has a smoother idle than conventional racing ignitions. Thanks to its fine balancing, it keeps vibrations low even at high speeds. The stator was designed to withstand high heat loads so that no failures occur even at full power. Care has also been taken to ensure that the ignition is always easy to install and adjust. This makes it probably the most reliable racing ignition on the market.

Grippy tyres by Vee Rubber

From everyday tyres to studded and full slick. Founded in 1977, the Thai tyre manufacturer Vee Rubber offers a wide range of stylish tyre designs for every surface with an excellent price-performance ratio.