Getriebe & Gehäuse (Motor)

Shim 16/22/0.5

Nominal diameter: 16 mm · Material: Steel · Surface: blank / oiled · Ø inside: 16 mm · Ø outside: 21 mm · Thickness: 0.5 mm

Shim 15/21/0.5

Nominal diameter: 15 mm · Material: Steel · Surface: blank / oiled · Thickness: 0.5 mm · Ø inside: 15 mm · Ø outside: 21 mm

17 mm circlip E50 & ZA50 motor

Fuse type: Outside · Manufacturer: Puch · Material: Spring steel · Surface: gas nitrided · Ø inside: 15.6 mm · Nominal diameter: 17 mm · Ø outside: 19.2 mm · Thickness: 0.9 mm · Place of use: Clutch

SKF 6203 C3 Ball bearing 17/40/12

Bearing cage: "-" Sheet steel cage ball-guided · Stock number: 6203 · Width: 12 mm · Inner ring width: 12 mm · Manufacturer: SKF · Ø outside: 40 mm · Bearing clearance: C3 · Bearing type: Deep groove ball bearing · Ø inside: 17 mm

GPO repair stud bolt M6/M8x106

Material: Steel · Surface: blue galvanized · Total length: 106 mm · Manufacturer: GPO · Thread type: M6x1 (standard thread) · Thread type: M8x1.25 (standard thread) · Thread length: 14 mm · Thread length: 18 mm

Set of stud bolts M6x35 burnished

Material: Steel · Surface: burnished · Total length: 35 mm · Diameter: 6.1 mm · Thread type: M6x1 (standard thread) · Thread length: 11.5 mm · Thread length: 17 mm · Strength class: 8.8

Shim 19/26/0.3

Material: Steel · Surface: blank / oiled · Nominal diameter: 19 mm · Thickness: 0.3 mm · Ø outside: 26 mm · Ø inside: 19 mm

NTN 6203 C4 ball bearing 17/40/12 engine | Puch E50

Material: Steel · Surface: blank · Bearing cage: "-" Sheet steel cage ball-guided · Stock number: 6203 · Width: 12 mm · Inner ring width: 12 mm · Manufacturer: NTN · Ø outside: 40 mm · Bearing clearance: C4 · Bearing type: Deep groove ball bearing · Area of application: Standard · Ø inside: 17 mm

Shim 19/26/0.5

Nominal diameter: 19 mm · Material: Steel · Surface: blank / oiled · Thickness: 0.5 mm · Ø inside: 19 mm · Ø outside: 26 mm

Shim 13/19/1.0

Material: Steel · Nominal diameter: 13 mm · Thickness: 1 mm · Ø outside: 18.8 mm · Ø inside: 13.2 mm

Thrust washer 17/26/1.1 Gearbox

Material: Steel · Surface: hardened & ground · Thickness: 1.1 mm · Ø outside: 26 mm · Ø inside: 17 mm

Shim 20/28/0.5 Crankshaft E20 Bearing | Puch

Material: Steel · Surface: blank / oiled · Nominal diameter: 20 mm · Thickness: 0.5 mm · Manufacturer: Puch · Ø outside: 28 mm · Ø inside: 20 mm

swiing® revival shim 10.1/22.3/2

Material: Spring steel · Surface: Hardened · Nominal diameter: 11 mm · Tolerance: DIN 988 (-0.03 mm) · Thickness: 2 mm · Manufacturer: swiing® revival parts · Ø outside: 22.3 mm · Ø inside: 10.1 mm

Buzzetti rubber Ø16.5/20x40 foot control / kick starter / brake lever

Material: Rubber · Surface: grooved · Color: black · Total length: 40 mm · Manufacturer: Buzzetti · Ø outside: 16.5 mm · Ø outside: 20 mm · Ø inside: 7.1 mm

NSK 16005 Ball bearing 25/47/8 Gearbox | Zündapp Belmondo (Type 247)

Bearing cage: "-" Sheet steel cage ball-guided · Inner ring width: 8 mm · Manufacturer: NSK · Bearing clearance: CM (special/noise-reduced) · Surface: blank · Bearing type: Deep groove ball bearing · Material: Steel · Stock number: 16005 · Ø inside: 25 mm · Ball bearing closed: No · Ø outside: 47 mm · Width: 8 mm · Area of application: Standard

HPI extension cable ignition curve switch 2-pole ignition (45 cm)

Manufacturer: HPI · Number of cables: 2 pcs · Cable length: 350 mm

INA needle roller bearing 16/20.7/14.2 pinion shaft | Tomos

Material: Steel · Bearing cage: Sheet steel cage · Width: 14.2 mm · Manufacturer: INA · Ø outside: 20.7 mm · Bearing type: Needle sleeve · Area of application: Original · Area of application: Standard · Ø inside: 16 mm · Dimension needle bearing: 16/20.7 x 14.2 · Tomos spare part no.: 035502