Pinasco «EVOTEN» cylinder with 42 mm bore and 60 cc for your Piaggio Ciao, Si, Bravo, Boxer, Grillo moped / moped.
The completely üreworked 42 mm cylinder from Pinasco is now supplied with a 5-channel layout and the 5-fold bolted cylinder head manufactured for the highest loads. Various racing exhausts can be fitted to the supplied exhaust flange with 22.5 mm outer connection diameter.
The cylinder head is fitted without gasket. For optimum sealing, the tightening torque of 10 Nm for the M6 bolts and 14 Nm for the M7 stud bolts must therefore be observed.
The following parts are included in the scope of delivery:
- Additional bolts for the cylinder head
- Decompressor valve (actuation not included)
- Cylinder head empty
- Cylinder and accessories
- Piston with L-ring, rectangular ring and 12 mm piston pin (axe 12)
- Various gaskets for the cylinder base
- Cylinder head with L-ring, rectangular ring and 12 mm piston pin (axe 12);for the cylinder base
- Installation instructions in Italian
High-quality cast aluminum and durable Nikasil coating characterize this high-end tuning cylinder.
The cylinder kit develops maximum power in the mid to upper rev range. We recommend using the racing cylinder in combination with a variomatic drive.
Mounting on an original engine housing is only possible with major modifications. The cylinder kit can be mounted on the well-known Pinasco, Polini and Malossi racing cases without any adaptation work.
Note: If the cylinder kit is mounted on a Piaggio Ciao, this must be ground down on the cooling ribs on the right-hand side. However, due to the cut-out for the Ciao's cable duct, the hook on the head for the decompression cable is also missing. As a result, the cylinder cover is only suitable to a limited extent for Piaggio Si, Bravo of the newer generations or Grillo. This can be remedied by attaching the decompression cable to the cylinder head from the front, as with the Ciao or Boxer.
Corresponding add-on parts such as racing gearboxes, racing crankshaft, racing variator etc. can be found in the accessories section.
Quality product from the Italian manufacturer Pinasco.
| Manufacturer | Pinasco |
| Material | Aluminum |
| Surface | varnished |
| Displacement | 60 ccm |
| Crankshaft stroke | 43 mm |
| Nominal diameter | 42 mm |
| Ø Outlet outside | 22.5 mm |
| Ø piston pin (B) | 12 mm |
| Outlet type | clamped |
| Number of fixing points | 3 pcs |
| Area of application | Tuning |
| Decompressor | Yes |
| Camouflaged | No |
| Piaggio | Ciao - P, SC, PX, C24 Si Bravo / Super Bravo Boxer Grillo |
Ratings
Accessories & related products
swiing® ingenious needle roller bearing 12/15/16.2 "Racing" silver cage
Bearing cage: Silver cage · Manufacturer: swiing® ingenious parts · Ø outside: 15 mm · Bearing type: Needle roller and cage assembly · Width: 16.2 mm · Ø inside: 12 mm · Dimension needle bearing: 12/15 x 16.2 · Tomos OEM number: 035548
16,30 EUR
Not in stock
Polini Speed Engine engine housing electronic ignition | Piaggio Ciao, SI, Bravo, Boxer
Stock number: 6202 · Manufacturer: Polini · Width: 175 mm · Material: Aluminum · Surface: sandblasted · Crankshaft stroke: 43 mm · Total length: 215 mm · Color: silver · Ignition type: Electronic · Height: 104 mm
245,90 EUR
Polini Speed Engine engine case breaker ignition | Piaggio Ciao, SI, Bravo, Boxer
Stock number: 6202 · Manufacturer: Polini · Material: Aluminum · Color: silver · Crankshaft stroke: 43 mm · Width: 175 mm · Height: 104 mm · Total length: 215 mm · Ignition type: Breaker · Surface: sandblasted
245,90 EUR
Pinasco flywheel "Flytech" Carbon | Piaggio Ciao, SI, Bravo, Boxer
Manufacturer: Pinasco · Material: Aluminum · Material: Carbon · Ø Internal flywheel: 106 mm · Direction of rotation: right · Height: 38.7 mm · Weight: 650 g · Thread type: MF16x1 (fine pitch thread) · Surface: varnished · Ø cone small inside: 12.4 mm · Thread length: 7.5 mm · Ø cone large inside: 14.5 mm · Ø Flywheel outside: 135 mm · Cone length: 12.5 mm · Cone ratio: 1:5
245,90 EUR
swiing® revival stud bolt set M7x120 mm cylinder | Piaggio Ciao, SI, Bravo, Boxer
Manufacturer: swiing® revival parts · Material: Steel · Surface: galvanized (blue) · Thread type: M7x1 (standard thread) · Diameter: 6.2 mm · Total length: 120 mm · Drive: External hexagon · Strength class: 8 · Strength class: 8.8 · Thread length: 25 mm · Width across flats: 11 mm
13,70 EUR
swiing® ingenious stud bolt M7x120 / Ø 7.3 shank (10.9 strength)
Manufacturer: swiing® ingenious parts · Material: Steel · Diameter: 7.3 mm · Total length: 120 mm · Thread type: M7x1 (standard thread) · Surface: galvanized (blue) · Thread length: 20 mm · Thread length: 30 mm · Strength class: 10.9
5,75 EUR
Moped fans also bought
Collection only possible with online purchase and appointment.
