Pinasco «Slave» engine case with crankshaft (43 mm stroke / 12 mm KoBo) and double intake suitable for your Piaggio Ciao, Si, Bravo, Boxer, Grillo moped / moped.
The Pinasco «Power Casing» engine case is supplied with a specially developed crankshaft, which has a wider cheek for controlling the intake at the rear intake.
A standard 13 mm Dellorto SHA carburettor can be fitted to the rear of this case, as well as any side-mounted carburettor with a 24 mm connection on the reed system. The frame may have to be adapted in this case.
This dual carburettor system can be used to tease the last horsepower out of your motorcycle.
The following parts are included in the scope of delivery:
- Rear intake flange (connection 16 mm, &slash; inside 13 mm)
- Side diaphragm system incl. sealing plug for the 13 mm flange if this is not used.
- Mounting material for diaphragm flange (connection 24 mm, Ø inside 20 mm)
- Cylinder stud bolts
- Engine housing (Ø for cylinder neck up to 46 mm outside diameter)
- Engine housing screws
- ;crankshaft Pinasco Competition with 43 mm stroke and 12 mm piston pin (axe 12)
- Installation instructions in English & Italian
No housing gasket is supplied. Sealing compound is used for sealing.
We recommend using the 42 mm Pinasco cylinder kit for this racing gear. In addition, only electronic ignitions can be fitted to this housing.
If the engine is installed in a Piaggio Ciao frame, some material must be removed from the right-hand side of the housing and cylinder, as described in the installation instructions.
Corresponding add-on parts such as sealant, racing kit, racing ignition etc. can be found in the accessories section.
Quality product from the Italian manufacturer Pinasco.
Details
| Manufacturer | Pinasco |
| Material | Aluminum |
| Crankshaft stroke | 43 mm |
| Ignition type | Electronic |
Suitable for the following models
| Piaggio | Ciao - P, SC, PX, C24 Si Bravo / Super Bravo Boxer Grillo |
Accessories & related products
Dell'Orto 19 mm PHBG CS carburetor hand choke
Width: 70 mm · Total length: 82 mm · Height: 124 mm · Manufacturer: Dell'Orto · Material: Aluminum · Area of application: Racing · Area of application: Tuning · Component group Carburetor: Carburetor complete · Color: black · Nominal diameter: 19 mm · Carburetor type: PHBG CS · Choke control: Hand choke · Nozzle thread: M5x0.8 (standard thread) · Ø fuel hose connection: 5.4 mm · Ø fuel hose connection: 6 mm · Ø without reducing sleeve: 26 mm · Ø Inside entrance: 19 mm · Ø Internal connection: 24 mm · Ø Output inside: 19 mm · Ø Air filter connection: 32 mm · Ø Air filter connection: 60 mm · Air filter connection thread: MF32x1.25 (fine pitch thread) · Mounting type: Plug connection clamped · Mixed oil connection: Yes · Vacuum connection: Yes · Choke nozzle size: 60 · Camouflaged: No · Nozzle size: 75 · Size of secondary nozzle: 45
139,60 EUR
Malossi racing ignition 12V | Piaggio Ciao, SI, Bravo, Boxer
Manufacturer: Malossi · Area of application: High End · Area of application: Performance · Area of application: Racing · Material: Steel · Area of application: Tuning · Ø Internal flywheel: 80.5 mm · Light coil voltage: 12 V · Performance: 90 W · Direction of rotation: right · Number of fixing points: 2 pcs · Ø Flywheel outside: 105 mm · Ø Flywheel outside: 139.5 mm · Ø cable: 7 mm · Weight: 804 g · Weight: 890 g · Mounting type: Screws
465,60 EUR
SKF 6202 C3 ball bearing 15/35/11
Width: 11 mm · Bearing cage: "-" Sheet steel cage ball-guided · Inner ring width: 11 mm · Manufacturer: SKF · Bearing clearance: C3 · Stock number: 6202 · Bearing type: Deep groove ball bearing · Ø inside: 15 mm · Ø outside: 35 mm · Puch OEM number: 900.4.6202
11,50 EUR
Elring Dirko HT sealing compound gray (silicone) 70 ml permanently elastic up to 315°C
Manufacturer: Elring · Material: Silicone · Temperature resistance (min.): -60 - 315 °C · Area of application: Chemistry · Contents [ml]: 70 ml · Hazard warning: Causes damage to organs through prolonged or repeated exposure · Color: gray · Gap dimension (max.): 2 mm
23,20 EUR
331,43 EUR/l
Pinasco flywheel "Flytech" Carbon | Piaggio Ciao, SI, Bravo, Boxer
Material: Aluminum · Material: Carbon · Manufacturer: Pinasco · Surface: varnished · Height: 38.7 mm · Ø Internal flywheel: 106 mm · Thread type: MF16x1 (fine pitch thread) · Direction of rotation: right · Thread length: 7.5 mm · Ø cone small inside: 12.4 mm · Ø cone large inside: 14.5 mm · Ø Flywheel outside: 135 mm · Cone length: 12.5 mm · Cone ratio: 1:5 · Weight: 650 g
244,40 EUR
Dell'Orto 13/13 SHA carburetor hand choke | Piaggio Ciao P, SC
Material: Aluminum · Manufacturer: Dell'Orto · Total length: 55 mm · Width: 60 mm · Height: 110 mm · Area of application: Tuning · Component group Carburetor: Carburetor complete · Nominal diameter: 13 mm · Carburetor type: SHA (Piaggio) · Choke control: Hand choke · Nozzle thread: M5x0.8 (standard thread) · Ø fuel hose connection: 5.2 mm · Ø fuel hose connection: 6 mm · Ø without reducing sleeve: 18 mm · Ø Inside entrance: 13 mm · Ø Internal connection: 16 mm · Ø Output inside: 13 mm · Ø Air filter connection: 50.9 mm · Mixed oil connection: No · Mounting type: Plug connection clamped · Color: black · Vacuum connection: No · Camouflaged: No · Nozzle size: 66
81,40 EUR
Not in stock
Malossi oil seal FPM 15/24/5 A crankshaft | Piaggio Ciao, SI, Bravo, Boxer
Material: FPM / FKM (known as VITON®) · Manufacturer: Malossi · Surface: rubberized · Temperature resistance (min.): -30 - 200 °C · Width: 5 mm · Simmering type: A - With rubberized outer part / one sealing lip. · Place of use: Crankshaft · Ø inside: 15 mm · Ø outside: 24 mm
16,70 EUR
Pinasco 42 mm cylinder kit EVOTEN 12 mm KoBo | Piaggio Ciao, SI, Bravo, Boxer
Material: Aluminum · Manufacturer: Pinasco · Surface: varnished · Area of application: Tuning · Displacement: 60 ccm · Nominal diameter: 42 mm · Crankshaft stroke: 43 mm · Ø Outlet outside: 22.5 mm · Ø piston pin (B): 12 mm · Number of fixing points: 3 pcs · Outlet type: clamped · Decompressor: Yes · Camouflaged: No
430,70 EUR
Collection only possible with online purchase and appointment.
